Skip to content

Can You Plumb In a Heat Pump Tumble Dryer? Drain Hose Explained

Yes, many heat pump tumble dryers can be plumbed into a drain, so the collected water drains away through a hose instead of filling the container you empty after each load. Not every model supports this and the exact method varies, so always start with your own model's manual or installation guide.

How the water is collected on a heat pump tumble dryer

Unlike a vented tumble dryer, a heat pump model does not need a duct or hole to the outside. Instead, it extracts moisture from the drum air, condenses it into water, and collects that water in a removable container, sometimes called a water tank or reservoir. Your manual shows where it sits on your model.

When the container is full, the dryer will usually remind you to empty it. You pull the container out, tip it down the sink, push it back in and carry on. Plumbing the dryer into a drain takes care of that step for you. For more on how the system works, see our guide on what a heat pump tumble dryer is and whether it is worth the extra cost.

Can you plumb in a heat pump tumble dryer?

Many models allow it and have a drain connection for this purpose. Your manual shows where it is. The hose carries the water away as the dryer runs, feeding into a sink waste, a standpipe, or a shared waste pipe that already serves your washing machine, provided the manual permits that arrangement.

A dryer drain carries only the water condensed from your laundry. There is no water inlet. The dryer does not take in water from the mains, so do not confuse the drain outlet with a washing machine's water supply hose. You are adding one outgoing hose only.

Check the manual or product page for whether a drain kit is supplied with your model, or whether you need to source a compatible hose and adaptor separately. If the connection point is not described in your manual, the model may not support permanent plumbing, so contact the manufacturer before proceeding.

What to check before you start

  • The manual. Confirm your model has a drain outlet and that permanent plumbing is described as supported. The manual will also specify any height limits for the hose route. Follow these exactly.
  • A suitable drain point. You need a sink waste, standpipe, or shared waste pipe within reach of the hose without stretching or kinking it. If there is no existing drain point nearby, you may need a plumber to fit one.
  • Kink-free routing. Plan the hose path so it runs smoothly to the drain within the height limits in the manual. Kinks can stop the water draining properly.

General steps

These steps describe the process in broad terms. Always follow your model's manual, which overrides anything here.

  1. Switch the machine off at the wall and unplug it before doing anything else. You will need to pull the dryer forward to reach the back, so leave enough space behind it to work.
  2. Read the installation section of your manual and gather any parts it specifies, such as a drain hose, elbow adaptor, or retaining clip.
  3. Pull the dryer away from the wall carefully, keeping the power cable safe.
  4. Locate the drain outlet on the back or base of the machine as shown in the manual, and attach the hose according to the manufacturer's instructions.
  5. Route the hose to the drain point, following the path and height guidance in the manual. Secure it so it cannot slip, and confirm there are no kinks.
  6. Connect the other end to the drain, into a sink waste, standpipe, or washing machine shared waste as your manual describes and as your installation allows.
  7. Push the dryer back into position, plug in, and run a short cycle to confirm water drains freely and no leaks appear at either end of the hose.

If the installation requires new pipework, for example adding a standpipe or a new waste branch, use a qualified plumber or installer. Do not modify the appliance itself or remove panels beyond what the manual describes.

Common problems after plumbing in a heat pump dryer

Water still collecting in the container. On some models the container stays in place after plumbing in. Check the manual to see whether some water in the container is expected on your model. If it fills as it did before, or the empty-container warning still shows, the water is not reaching the drain, so check the hose connection is fully seated and check the route.

Hose kinked or too high. The drain hose must stay within the height limits in your manual and be free of kinks. If it is kinked or routed too high, the water may not drain properly. Re-route the hose as the manual shows. If the problem continues, consult the manual's troubleshooting section, then contact the manufacturer or a qualified engineer.

For guidance on keeping the filters and water container in good condition once the dryer is set up, see our filters and water container care checklist. If you are still deciding where to site the machine, our guide on whether heat pump tumble dryers work in cold rooms and garages is worth reading first.

Choosing a heat pump tumble dryer

If you are still choosing a model, browse our full range of heat pump tumble dryers. Examples from our range include the Hotpoint 8kg Heat Pump Tumble Dryer with PetHairCare - White, the Hotpoint 9kg Fabric Care Heat Pump Tumble Dryer with HomeWhiz - Grey, the Indesit 8kg Heat Pump Tumble Dryer with QuickCycle - White, and the Indesit 9kg Heat Pump Tumble Dryer with Steam Technology - Black. Check each product page and the accompanying manual for drain outlet details before buying if permanent plumbing is a priority for you.

Models to compare

These heat pump and vented dryers are worth comparing if you are choosing a model to plumb in.

Plumbing in a heat pump dryer: FAQ

Can you plumb in a heat pump tumble dryer?

Many heat pump tumble dryers have a drain outlet that lets you connect a hose and route collected water directly to a sink waste or standpipe, so you no longer need to empty the container manually. Whether your model supports this depends on the model, so check the manual or product page first.

Do I still need to empty the water container?

Once plumbed in correctly, you should not need to empty the container after each cycle. Check the manual to see whether some water in the container is expected on your model. If the container fills as before, check that the hose is routed and connected as the manual describes.

Can a tumble dryer share a drain with a washing machine?

Some manufacturers allow the dryer's drain hose to connect to the same waste branch as a washing machine. This depends on your model and your existing pipework, so always confirm it is described as acceptable in the dryer's manual before connecting to a shared waste.

Does a heat pump tumble dryer need a vent?

No. A heat pump tumble dryer condenses moisture internally and collects it as water. It does not need a duct, hole or vent to the outside. This makes it suitable for rooms where venting to the outside is not possible.

Cart 0

Your cart is currently empty.

Start Shopping