Electrical Safety First recommends cleaning the lint filter and clearing door fluff after every use. Let your tumble dryer cool and unplug it before cleaning. Wipe the drum and empty the water tank, then follow the cleaning steps for your condenser, heat-pump filter or vent hose below.
| Part | Routine | Care point |
|---|---|---|
| Door filter and door area | After every cycle | Remove loose fluff before another load. |
| Drum | Hotpoint’s guide: monthly | Wipe with a soft cloth and non-abrasive cleaner. |
| Water tank | Empty the collection tank | A full tank can pause drying. |
| Condenser or heat-pump filter | Interval for the fitted component | Wash only removable parts approved for rinsing. |
| Vented hose | Hotpoint’s guide: every three months | Keep the air route clear and free of kinks. |
How do you clean the lint filter?
Start with a cool appliance switched off and unplugged. Use the filter’s release or handle as shown in your model’s manual; it also identifies washable parts and cleaning intervals.
- Lift out the door filter.
- Open the filter’s mesh leaves.
- Lift fluff away with your fingers or a soft cloth.
- Put the lint in the bin.
- Wipe the accessible filter housing and door opening.
- Inspect the mesh for tears or damage.
- Close the filter and refit it securely.
Hotpoint’s cleaning guide also describes rinsing washable filters under a tap. Let a rinsed filter dry completely before refitting it.
A filter behind another filter needs separate attention. Lift removable sections out individually and clean each mesh surface. Leave fixed panels in place; hidden ductwork belongs with a repair technician.
How do you wipe the drum, door and sensors?
Wipe the empty drum and inside of the door with a soft cloth and a non-abrasive cleaning product. Apply cleaner to the cloth rather than spraying into openings. Remove loose items before wiping, then leave the door open while the surfaces dry.
Clean accessible dirt from the door seal gently. Hotpoint also recommends wiping the cabinet’s front, sides and back with a soft cloth and non-abrasive cleaner. Keep liquids away from controls and openings. Skip abrasive pads and metal scrapers.
Sensor bars detect moisture in the laundry. On the layout shown in Hotpoint’s guide, they sit behind the lint filter at the front door opening. Wipe the metal bars with a soft cloth and dry them afterwards. Other layouts need their own care instructions.
What changes between condenser, heat-pump and vented dryers?
Match the cleaning job to the part fitted. A removable condenser cassette and a heat-pump evaporator need different treatment, even when their access covers look similar. A vented dryer needs its hose checked instead.
Beko’s cleaning guide describes a removable condenser with release catches. Release those catches, slide out the unit and rinse away lint. Let the water drain and the unit dry before refitting it. Fasten the locks and close the cover.
On the heat-pump layout in Beko’s guide, open the removed filter drawer and take out the sponge. Wipe it with a damp cloth; rinse under running water if needed. Dry it fully, then refit it without squeezing it into the drawer. Keep this washable sponge separate from the evaporator: vacuum that assembly only when dry, without bending or touching its sharp fins.
For a vented model, inspect the accessible hose for crushing, kinks and lint. Disconnect it only with the appliance unplugged. Clean the removable hose and reconnect it securely, keeping it clear when the appliance returns to position.
When comparing care routines, the Indesit CYSD72DWWUK heat-pump dryer is a 7kg heat-pump model. The Indesit CYDA81WWGLUK vented dryer is an 8kg vented model, so include its hose route in your installation plan.
How do you empty the water tank?
Beko’s end-of-programme reminder calls for emptying the tank after each cycle where it collects the drying water. Pull the collection tank out carefully, keep it level and empty it into the sink. Slide it fully back into position.
A full-tank warning during drying calls for emptying the tank before continuing. Keep the warning separate from the filter reminder: they refer to different jobs. If the same tank warning returns after emptying and refitting, record it for the repairer.
What if drying is still slow after cleaning?
Check the load and selected programme before adding more drying time. A clogged filter or hose restricts the air route, but cleaning alone cannot diagnose a heater or electrical fault. Use this table to decide what needs attention next.
| Symptom | Possible cause | Your next action | When to call a technician |
|---|---|---|---|
| Longer drying | Lint restricting airflow | Clean accessible filters and inspect the hose. | Poor drying continues after those checks. |
| Tank warning | Tank full or not fully seated | Empty and refit the collection tank. | The warning returns with an empty tank. |
| Filter reminder | Accessible lint build-up | Clean and refit all user-removable filters. | The reminder persists after correct care. |
| Burning smell or scorching | Possible electrical fault | Stop use and unplug if safe. | Before using the appliance again. |
Describe the programme, load and warning message when asking for help. Mention which parts you cleaned. That gives the technician a useful starting point without opening the appliance yourself.
Safety check
Stop use and unplug if you notice burning smells or scorch marks. Follow Electrical Safety First’s safety advice and avoid unattended or overnight drying. Some older Hotpoint and Indesit dryers have a lint-related recall: use the manufacturer’s model and serial-number checker. An affected dryer must remain unplugged until the manufacturer resolves it. Also check GOV.UK recalls and alerts.
If you need a replacement
The Indesit CYSD72DWWUK 7kg Heat Pump Tumble Dryer with QuickCycle - White is a heat-pump option when you are comparing the care routines above.
The Indesit CYDA81WWGLUK 8kg Vented Tumble Dryer - White is a vented option with a hose route to plan.
Frequently asked questions
Can I use white vinegar on the moisture sensor?
Hotpoint’s cleaning guide allows a soft cloth dampened with white vinegar on its sensor bars. Dry the bars with a soft cloth afterwards. Keep this method to the sensor surfaces the manufacturer identifies; it is not permission to pour vinegar into the appliance or soak filters and electrical parts.
Can I vacuum the heat exchanger?
Beko’s guide permits gentle up-and-down vacuuming of the evaporator it describes, provided it is dry. Keep the nozzle from bending the sharp fins and avoid bare-hand contact. Use this method only for the matching accessible assembly; fixed or different heat exchangers need their own care method.
How do I clear lint from the water-tank funnel?
Beko’s water-tank instructions say to rinse accumulated lint from the funnel under running water. This is the tank’s funnel, separate from the evaporator and its filter drawer. Empty collected water first, then slide the tank carefully back into its housing.
Should I stop a cycle early to clean the dryer?
Let the programme reach its end before starting routine cleaning. Its finishing stage matters for cooling the laundry. If you have to stop a cycle, Electrical Safety First says to remove all items quickly and leave the door open so heat escapes. Wait for cooling before handling cleaning parts.
Can I dry clothes stained with oil after cleaning the drum?
Clothes contaminated with oils, fats, grease or solvents need separate attention. Electrical Safety First says to clean them without using a tumble dryer. A freshly wiped drum does not change that advice. Keep contaminated cleaning cloths out of the next load and choose a suitable alternative drying method.
If replacement follows a diagnosis, compare our tumble dryers and heat-pump tumble dryers, then check the filter access and installation instructions for the model you choose.
Related guides
- Heat-pump tumble dryer filter-cleaning checklist
- How to maintain your tumble dryer
- How long a tumble dryer takes
Sources
- Electrical Safety First - Tumble dryers usage and safety. Checked 18 November 2026.
- Hotpoint - Step-by-step guide on how to clean your tumble dryer. Checked 18 November 2026.
- Beko UK - How to clean a tumble dryer. Checked 18 November 2026.
- Hotpoint/Whirlpool - Tumble dryer safety model checker. Checked 18 November 2026.
- GOV.UK - Product recalls and alerts. Checked 18 November 2026.
Last updated: 18 November 2026. Author: Go Assist.


